Hot Tubs and Spas | Hampton Roads

Hot tub and spa electrical installation in Hampton Roads, ready before the tub arrives.

We show you what your tub needs and what your panel can carry. You decide what is best for your home.

What electrical work does a hot tub need?

Most hot tubs need a dedicated circuit, GFCI protection, a disconnect within sight of the tub, and grounding and bonding, all sized to what the manufacturer calls for. Current Contracting checks your panel, plans the wire path, explains what the tub needs, and puts the cost in writing for homes across Hampton Roads.

Stakes

Is the wiring ready for the day the hot tub shows up?

Hot tubs arrive on a delivery date. The electrical has to be done before you can use it, and permitted work may need an inspection too.

And water plus electricity is not the place for a shortcut.

WHAT YOU GET

What you get before the tub is delivered

Clarity.

You will know what circuit the tub needs, where the disconnect goes, and whether your panel can carry it.

The right fix.

Wired to the manufacturer instructions and local code, with the bonding done. Not a borrowed circuit or an extension cord.

A plan in writing.

The work and the cost, before anything starts.

GUIDE

You should not have to guess if your hot tub is wired safely.

A hot tub is a big purchase. The wiring is the part you will never see, and the part that matters most for safety.

We read the spec sheet with you, check the panel, and explain the plan. We handle the permit and inspection when the job needs them.

THE PLAN

How it works

1

Book your free Home Assessment

Tell us the make and model, and where the tub will sit.

2

We walk the spot and the panel with you

and explain what we find.

3

Get a written plan and cost

then decide.

WHY THIS MATTERS

What does a hot tub electrical installation include?

WHY THIS MATTERS

120 volt or 240 volt?

Some smaller plug in tubs run on 120 volts and plug into a dedicated GFCI protected outlet. Most larger tubs need a hardwired 240 volt circuit.

The manufacturer spec sheet decides the circuit size. We read it before we quote.

WHY THIS MATTERS

What are grounding and bonding, and why do they matter?

Grounding gives a fault a safe path. Bonding ties the metal parts around the tub together, so there is no difference in voltage between them.

Both are code requirements for hot tubs and spas. The details vary by locality and by where the tub sits.

WHY THIS MATTERS

Where should the tub go?

Code sets distances between a tub and overhead power lines, outlets, and lights. The distance from the panel sets how long the wire run is.

Decks, patios, and driveways in the way change the route. We check the spot before you pour a pad or build a deck.

Near the water, salt air and moisture are hard on outdoor electrical parts. We use outdoor rated equipment and sealed connections.

WHY THIS MATTERS

Does your panel have room for a hot tub?

A 240 volt hot tub is a large load. Some panels have room. Some need a load calculation, a subpanel, or a service upgrade first.

We tell you which one you are in before we quote.

WHY THIS MATTERS

So what is this going to cost?

It depends on the tub, the distance from the panel, what is in the way, and whether the panel has room.

A plug in tub next to the house and a 240 volt tub across the yard from a full panel are not the same job.

So we come look, explain what the tub needs, and put the cost in writing. There is no charge for the assessment.

WHY THIS MATTERS

Have the spec sheet already?

Send it over with a photo of your panel and the spot where the tub will go. We will tell you what we see.

Related services

Electrical Panel Replacement and Service Upgrades.

If the panel cannot carry the tub.

Electrical Subpanel Installation.

A panel closer to the backyard.

Outdoor & Security Lighting.

Light the path to the tub.

Outlet, Switch & GFCI Installation.

Weatherproof outlets for the patio.

FAQ

Common questions about hot tub electrical

Does a hot tub need a dedicated circuit?

Most do. Larger tubs usually need a dedicated 240 volt circuit. Some smaller plug in tubs use a dedicated 120 volt GFCI protected outlet. The manufacturer instructions decide it.

Yes. Code calls for GFCI protection on hot tubs and spas. Where the GFCI sits, in the panel or in the disconnect, depends on the setup.

Code generally calls for a disconnect within sight of the tub and a minimum distance from the water. Exact requirements vary by locality. We place it where code calls for it and where it is easy to reach.

Usually. Hot tub wiring is the kind of work that generally needs a permit and an inspection, but requirements depend on your city or county. We tell you what applies.

Only if it is a 120 volt plug in model made for it, on a dedicated GFCI protected circuit. Do not use an extension cord. Larger tubs need a hardwired circuit.

It depends on the tub. Many larger tubs use a 40 or 50 amp, 240 volt circuit, but the spec sheet decides. We size the wire and breaker to match.

Want your hot tub wiring sorted before delivery day?

We will check the spot and the panel, explain it, and put it in writing. Then you decide.